Westlake Publishing Forums
July 26, 2021, 02:54:18 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:     REGARDING MEMBERSHIP ON THIS FORUM: Due to spam, our server has disabled the forum software to gain membership. The only way to become a new member is for you to send me a private e-mail with your preferred screen name (we prefer you use your real name, or some variant there-of), and email adress you would like to have associated with the account.  -- Send the information to:  Russ at finescalerr@msn.com
 
   Home   Help Search Login  
Pages: [1]
  Print  
Author Topic: Diner with 'neon' sign  (Read 7703 times)
voyager
Jr. Member
**
Offline Offline

Posts: 51


« on: March 12, 2013, 03:10:45 PM »

Ok, so it was 'suggested' there may be some interest in the sign on this mini dio I made for a friend to display his 1/24th models. As such, it is not up to the standards normally shown on here but I used EL wire (electro Luminescent) for the 'neon' sign which I think looks quite effective. Due to the construction of the wire, it is not possible for even this 1.3mm dia. to bend at a sharp 90 degree angle, so I hand painted the lettering onto 1mm plastic sheet then cut around it and glued that to another sheet of 1mm. I then drilled holes where the wire appears and disappears but at an angle so the wire is not forced in a sharp bend to lie 'flat' on the sign. (sorry, I didn't take progress photo's!). I used 2 x 1m lengths of the wire - they come with plugs attached so I threaded the it in and out without bending it too sharp on the back, hence the cut out in the building to allow for the depth of these wires. You can cut them to length easily but as I had around 10" left, I glued this along the inside top of the windows to give a glow to the interior (It's only about 1" deep and drawn with coloured pencils so kept fairly indistinct). This is powered by a 3v battery pack which has 4 positions - off/on/slow flash/fast flash but the company does packs with up to 12v which apparently make it glow brighter! My main problem was gluing the stuff! I tried superglue, both thick and thin and 5 minute epoxy, none of which would hold it, especially as it 'springs' somewhat and plastic cement doesn't touch it. I ended up bending each letter then using a hot glue gun to stick it then before it set fully, cut any excess off with a scalpel, leaving glue just under the wire. I also glued the back where each wire goes in and out to stop movement.











the company I got the bits from was http://myworld.ebay.co.uk/elwirecraft&ssPageName=STRK:MEFSX:SELLERID&_trksid=p3984.m1543.l2533  who had great service, answers questions quickly and has some good tips on the website.
« Last Edit: March 12, 2013, 03:14:27 PM by voyager » Logged

Andrew

If it has wheels, I'll have a look!
Gordon Ferguson
Hero Member
*****
Offline Offline

Posts: 1070


« Reply #1 on: March 12, 2013, 03:22:21 PM »

Still think it is very effective Andrew......... The coloured pencil interior work well too.

I like the design of the building , with a less fancy sign and the addition of a sooty steel chimney to remove the smole from the  "fry ups" would make a good late fifties early sixties Tranport cafe for your Foden  Wink
Logged

Gordon
voyager
Jr. Member
**
Offline Offline

Posts: 51


« Reply #2 on: March 12, 2013, 03:30:58 PM »

Someone was in there fast Grin  The Foden is with Steve for casting..... Wink

I forgot to mention, the company also do el panels you can cut out letters from or you could mask over to leave 'lit' areas and they also do 'chasing' wire - be good around signs and also animated panels.
Logged

Andrew

If it has wheels, I'll have a look!
Ray Dunakin
Hero Member
*****
Offline Offline

Posts: 4473



WWW
« Reply #3 on: March 12, 2013, 09:55:34 PM »

Nice looking model, and great job with that EL wire! Thanks for posting how you did it. I wanted to use some for a sign on the 1/24th scale hotel I made last year, but the sign would have been much smaller and there was no way to make the EL fit it. I still may try panels that can be cut to shape, if I can come up with a design I like.

Logged

Visit my website to see pics of the rugged and rocky In-ko-pah Railroad!

Ray Dunakin’s World
finescalerr
Administrator
Hero Member
*****
Offline Offline

Posts: 6052


« Reply #4 on: March 13, 2013, 01:30:26 AM »

I had no idea how somebody would reproduce a functional neon sign. Now I finally know. -- Russ
Logged
Chuck Doan
Mr. Wizard
Hero Member
*****
Offline Offline

Posts: 2575



WWW
« Reply #5 on: March 18, 2013, 01:31:32 PM »

Very effective!
Logged

“They're most important to me. Most important. All the little details.” -Joseph Cotten, Shadow of a Doubt





http://public.fotki.com/ChuckDoan/model_projects/
voyager
Jr. Member
**
Offline Offline

Posts: 51


« Reply #6 on: March 19, 2013, 01:46:39 AM »

Thank you gents. I realise the actual model is not up to standard but I am pleased with the el wire and will be using more in future. Just need to study Kens' work more...... Grin
Logged

Andrew

If it has wheels, I'll have a look!
Pages: [1]
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.13 | SMF © 2006-2011, Simple Machines LLC Valid XHTML 1.0! Valid CSS!