• Welcome to Westlake Publishing Forums.
 

News:

    REGARDING MEMBERSHIP ON THIS FORUM: Due to spam, our server has disabled the forum software to gain membership. The only way to become a new member is for you to send me a private e-mail with your preferred screen name (we prefer you use your real name, or some variant there-of), and email adress you would like to have associated with the account.  -- Send the information to:  Russ at finescalerr@msn.com

Main Menu

Feldbahnmodule with ship

Started by fspg2, April 21, 2011, 12:42:16 AM

Previous topic - Next topic

Bernhard

That looks absolutely realistic.

Bernhard

fspg2

#1081
The windows have all been installed in the meantime, and the window sills have been mounted in front of them.

Alter_Lagerschuppen_345 (fspg2)


There's definitely a certain resemblance to the prototype.

Rotstein_Lagerschuppen_01_Helmut_Schmidt_ (fspg2)


Inside the old storage shed there's a motor-driven winch for the crane beam. Its mounting anchors pass through the wall and are secured on the outside of the gable front with iron plates.

Alter_Lagerschuppen_339 (fspg2)


Alter_Lagerschuppen_340 (fspg2)


Alter_Lagerschuppen_341 (fspg2)


Alter_Lagerschuppen_342 (fspg2)


I already reported on the construction of the winch in detail back in 2009 -

have a look: https://www.buntbahn.de/viewtopic.php?t=6691&start=190 - and https://www.buntbahn.de/viewtopic.php?t=6691&sid=f4dec3997d457db62e1d8ccbcec7ce94&start=210


Now it was time to continue. First, the "iron plates" were milled from 0.3 mm nickel silver, and 1.0 mm brass threaded rods were soldered to M1.0 nuts. Then everything was sandblasted and blackened.

Alter_Lagerschuppen_343 (fspg2)


The already pre-assembled winch was pushed, with its threaded rods, through the six 1.1 mm holes drilled in the gable wall...

Alter_Lagerschuppen_346 (fspg2)


...and secured from the outside with the small anchor plates and M1.0 nuts.

Alter_Lagerschuppen_346 (fspg2)


To make it easier to pick up the tiny M1.0 nuts with the nut driver, I simply set them with their bottom sides on the sticky side of Tesa masking tape. That eliminates the tedious fiddling with my fingers, and the work goes much faster.

M1.0 nut with nut driver (fspg2)


I found it a bit tricky to solder the fork for the cable pulley at a right angle to the bent nickel-silver strip (0.2 mm thick, 1.5 mm high). The 1.0 mm holes will later accept the 1.0 mm axle of the cable pulley, so they had to line up exactly.

To align them, I had originally planned to use a 1.0 mm brass wire that I had colored black with a permanent marker, since marker ink usually works as a solder resist. With parts this small, though, I wasn't sure I'd be able to get the wire back out afterward without damaging the thin nickel-silver sheet. I didn't have a wire made of silver steel that thin, which solder wouldn't stick to in the first place.

Volker came up with the solution (many thanks for that!): the shank of a 1.0 mm drill bit aligned both parts reliably and didn't pick up any solder. A small block of Pertinax (phenolic laminate) served as a stop to ensure the right angle. I did the soldering with a 12 V / 8 W soldering iron.

Alter_Lagerschuppen_344 (fspg2)
Frithjof

Barney

Exceptional work  - so realistic and true to the prototype
Barney
Never Let someone who has done nothing tell you how to do anything
Stuart McPherson

Bill Gill


Hauk

Very nice, as always!
Were do you get your M1.0 nuts, by the way?
Regards, Hauk
--
Statement of authencity: All the content in this post was made without using AI in any form. This includes the modelling, the photography, post-prosessing and writing.

Remembrance Of Trains Past

fspg2

Frithjof

Stuart

Well done!  Excellent work!

Stuart

finescalerr

Most satisfactory and the closer you get the better it looks. -- Russ

fspg2

The top of the front wall is finished off with four finials and a row of roof tiles.

Alter_Lagerschuppen_325 (fspg2)


Alter_Lagerschuppen_326 (fspg2)


Alter_Lagerschuppen_327 (fspg2)


Alter_Lagerschuppen_328 (fspg2)


I sawed the finials out of Ureol (a modeling board material). First, I cut three small square blocks (19.1 mm x 14.2 mm) on the Proxxon circular saw. (A mask was a must, of course; you shouldn't breathe in the dust!!!) Then I sawed all sides at both ends of the three blocks at a 45° angle. A stop made sure all the lengths came out the same.

Alter_Lagerschuppen_329 (fspg2)


Next, I moved on to the Böhler circular saw with a 0.3 mm blade, where I finally cut off six identical finials. Even though I only need four for the building, I made two extra... you never know where they sometimes hide ;-).

Alter_Lagerschuppen_330 (fspg2)


Alter_Lagerschuppen_331 (fspg2)


As described earlier, after sandblasting, the white-metal roof tiles were pretreated with a black etching solution. Then I brushed all the tiles several times with diluted Plaka paint (brick red).

Doppelfalzziegel 1:22,5_01 (fspg2)


Alter_Lagerschuppen_348 (fspg2)


Alter_Lagerschuppen_349 (fspg2)
Frithjof

finescalerr

Perfect (of course). -- Russ

lab-dad

Beautiful - EVERTHING!
I have used liquid graphite to keep solder from sticking.

MJinTN

Bernhard

Great job! I love it.

Bernhard

fspg2

@MJinTN
I've used liquid graphite to keep the solder from sticking.

Thanks for the tip! I'd love to try that!


A house, and an old storage shed too, usually has not just windows but also doors and often gates as well.

Let's start today with the upper gate.

Alter_Lagerschuppen_335 (fspg2)


Admittedly, it has seen better days. Many of the damaged spots were even more noticeable from the inside.

Alter_Lagerschuppen_336 (fspg2)


A first tracing of the boards was printed out at 56.8 mm wide and 81.0 mm high and held up to the model to check the dimensions.

Alter_Lagerschuppen_350b (fspg2)


The interior view was scaled to the same dimensions and served as a template for the individual boards.

Alter_Lagerschuppen_350 (fspg2)


So that the individual slats wouldn't keep slipping, I had first stuck a small strip of Gudy 870 adhesive film onto the drawing.

Alter_Lagerschuppen_355 (fspg2)


Once everything was done, I could determine the positions of the 0.8 mm drill holes for the strap hinges. Placed in a milled pocket in MDF and secured against slipping with masking tape, the holes were drilled on the CNC mill.
I had already milled the strap hinges vertically from 2.0 mm MS58 brass many years ago.

Alter_Lagerschuppen_351 (fspg2)


The triangular peak was made as well.

Alter_Lagerschuppen_352 (fspg2)


Alter_Lagerschuppen_354 (fspg2)


The door pintle, or historically the "Kloben" (gudgeon hook), was milled from 0.3 mm nickel-silver sheet and had a 0.8 mm rivet soldered in at a right angle.

Alter_Lagerschuppen_357 (fspg2)


A 12 volt/8 watt soldering iron and a drop of liquid flux helped me apply a tiny amount of solder to the rivet head.

Alter_Lagerschuppen_361 (fspg2)


Alter_Lagerschuppen_358 (fspg2)


This morning, the parts were loosely positioned on the shed for the first time.

Alter_Lagerschuppen_359 (fspg2)


Hardly had the "new" gates been put in place when the old fellow this evening had to be a little surprised... not even stained yet, and with properly screwed-on strap hinges, and already some of the boards are broken... :shock:

Alter_Lagerschuppen_360 (fspg2)
Frithjof

lab-dad

That last part made me laugh out loud!
Thank you!
Mj

Bernhard

That's simply model building at its finest. Congratulations.

Bernhard