Westlake Publishing Forums

General Category => Modellers At Work => Topic started by: Chuck Doan on October 27, 2026, 08:11:46 PM

Title: New project
Post by: Chuck Doan on October 27, 2026, 08:11:46 PM
I have been plugging along on a 1/16th scale picture frame diorama. It is based on a former garage/auto shop located in Keeler California, just up the street from the SP narrow gauge depot. It is a corrugated metal building with what appears to be a plywood and plaster false front. It is directly adjacent to the Keeler Market, another often photographed building in that town.

I have several photos from different time periods showing its continued deterioration. The false front is leaning out perilously in the later pics, and the 6 pane window is gone. The exposed cloth in the left window has almost disappeared over time.

Initial plan is a cropped section featuring the windows and small door. Certainly not the whole front, which would be over 30" long in my scale. I am not attempting to copy it exactly, but I hope it will be Pretty Damn Close.
Title: Re: New project
Post by: Chuck Doan on October 27, 2026, 08:15:19 PM
This is likely the crop I will do. I modeled it up in scale using Solidworks to make the layout drawings.
Title: Re: New project
Post by: Chuck Doan on October 27, 2026, 08:17:22 PM
Most of the window panes have plywood inserts, and some have cloth stretched over them for some reason.
For the plywood, I used .015 thou thick birch plywood from Midwest Products. I used Silverwood stain as a first coat, and then a wash of Prismacolor Primer "paint" (rub a pencil on a square of sandpaper and then pick up with water and a brush.) Then seal with Dullcote and draw on the grain freehand with contrasting Prismacolor pencils. I print out pictures of actual plywood, scaled down to the size of the window. I use these as a sizing guide for the freehand grain.
A few panes still have glass in them. I used microscope cover slide glass for these. I haven't seen any broken glass remnants in any of the photos.
Title: Re: New project
Post by: Chuck Doan on October 27, 2026, 08:29:28 PM
The window frames are made from various sizes of dimensional basswood.  The basic process for each piece is a light brushing with a fine wire brush, and then a coat or two of Silverwood stain. Then I apply wood color by dipping various Prismacolor pencils in Silverwood , or rubbing alcohol and then rubbing the pencils on the wood.

The paint is done using Floquil Pollyscale Dark Green. First, Odorless Turps are applied to the piece, followed by one or two brushed out coats of paint. Then Scotch Magic tape is applied and removed to peel parts of the paint off.

The big window was done first.
Title: Re: New project
Post by: Chuck Doan on October 27, 2026, 08:43:09 PM
The smaller window was next. The cloth was simulated using stretched Teflon tape, the type used to seal pipe threads. This was an idea I had seen in the past, but I couldn't find the original reference, so I just winged it. Once applied, I used water thinned pigment powders to dirty it up.

The lower left and the upper right panes of the prototype still have glass in them (as do mine). Over time, the exposed cloth has almost completely deteriorated.
Title: Re: New project
Post by: Chuck Doan on October 27, 2026, 08:48:02 PM
Couple of sunny shots.  The backside shows how the teflon was stretched and pulled around the sides of the plywood inserts. I also left a hair for DNA analysis or later carbon dating use. No Salvator Mundi controversy for me!
Title: Re: New project
Post by: Chuck Doan on October 27, 2026, 09:35:21 PM
The door was next. I used the same plywood for the panels, but I sanded them thinner to about .008 thick (or thin). Then I glued them to a sub basswood panel with thin strips underneath so the plywood would warp. The latch was made from styrene bits and brass wire.

The sunny shot shows the warping plywood better.
Title: Re: New project
Post by: Chuck Doan on October 27, 2026, 09:40:11 PM
The three items placed on a scaled photo of the wall:
Title: Re: New project
Post by: Chuck Doan on October 27, 2026, 09:52:59 PM
Where it is today. Everything glued together and mounted to a handling plank. I am planning a deeper black background for the 3 larger windows. There will also be more fading/variations in the paint added, and a few nails. Then I have to figure out how to do the plaster walls.
Title: Re: New project
Post by: Hydrostat on October 28, 2026, 12:54:22 AM
What a pleasure! I'm amazed that the teflon accepted the color that good. It looks absolutely convincing.
Title: Re: New project
Post by: Bill Gill on October 28, 2026, 05:37:35 AM
Wonderful, Chuck.
The warped, delaminating plywood is especially good as is teflon tape fabric.
(How did you get the coloring to stick to teflon!?)
Title: Re: New project
Post by: Bernhard on October 28, 2026, 09:39:40 AM
An interesting scene, rendered very realistically.

Bernhard
Title: Re: New project
Post by: finescalerr on October 28, 2026, 11:36:33 AM
Superb. -- Russ
Title: Re: New project
Post by: Stuart on October 28, 2026, 12:52:25 PM
It's always a treat to see your projects and how you go about getting the results you do.  Your plywood process and torn and draped fabric effect are quite convincing.

Once I finish with my gas station/garage I plan to do, as you are suggesting with this post, focusing on much smaller projects I can actually accomplish within a reasonalble amount of time.

Stuart
Title: Re: New project
Post by: Hauk on October 29, 2026, 02:42:36 AM
There are modellers, and then there is Chuck.
Title: Re: New project
Post by: fspg2 on October 29, 2026, 04:28:31 AM
The King of Model Builders—it never ceases to amaze me that these wonderful pieces are just models!
Title: Re: New project
Post by: nk on November 06, 2026, 05:05:50 PM
Chuck, It's really something and exactly what I would expect. Nice work. I hope you are using archival adhesive tape.
Narayan