Westlake Publishing Forums
September 25, 2018, 08:37:53 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:     REGARDING MEMBERSHIP ON THIS FORUM: Due to spam, our server has disabled the forum software to gain membership. The only way to become a new member is for you to send me a private e-mail with your preferred screen name (we prefer you use your real name, or some variant there-of), and email adress you would like to have associated with the account.  -- Send the information to:  Russ at finescalerr@msn.com
 
   Home   Help Search Login  
Pages: [1]
  Print  
Author Topic: Silicon Rubber Molds  (Read 467 times)
Carlo
Full Member
***
Offline Offline

Posts: 172


« on: June 25, 2018, 03:02:32 PM »

I thought some of the great minds and deep experience here might help me with a problem.

I am having trouble with the silicon rubber used for molds, and could use some advice. For years, I have been successfully using Smooth-On OOMOO-30 for molds. Problem is the short shelf life (6 mo.). I only use it now and then in small quantities, for my own parts. I hate to buy a whole new quart every time, to get the 2 ounces that Iíll need at any given mold.  Any ideas or suggestions for other products?

Thanks,  Carlo
Logged
5thwheel
Sr. Member
****
Offline Offline

Posts: 304


« Reply #1 on: June 25, 2018, 08:28:58 PM »

Used to use a industrial grade of silicone RTV that used a catalyst. Would measure out just what i needed and freeze the leftover RTV.

Bill Hudson
Logged

Bill Hudson
Fall down nine times,
get up ten.
finescalerr
Administrator
Hero Member
*****
Offline Offline

Posts: 5151


« Reply #2 on: June 26, 2018, 12:55:19 AM »

Bob Uniack, an expert in that discipline, uses RTV silicone rubber and casting resin from Silpak, Inc. in Pomona, California. -- Russ
Logged
Bill Gill
Hero Member
*****
Online Online

Posts: 707



« Reply #3 on: June 26, 2018, 05:30:35 AM »

This is probably a fringe response, but I have read about people making small molds out of "plastic" worms sold in bait shops for fishing - melting them in a pot on the stove and reportedly being able to remelt and reuse them several times. I have also heard of people using silicon caulk to make small molds - not pure silicon which has a limited shelf life, but silicon-acrylic combinations. The caulk was thinned with water to for the first several layers.
Logged
Lawton Maner
Sr. Member
****
Online Online

Posts: 409


« Reply #4 on: June 26, 2018, 07:29:35 AM »

     Most of the "craft grade" molding compounds have a 6 month life from manufacturing to trashcan.  Depending on your needs you might be better off with small quantities of one of the "industrial" materials.

     I have successfully used the sink and shower silicon caulk to make small flat backed molds.  Since it is an adhesive. the pattern needs to be waxed before coating.  Petroleum jelly thinned with naphtha has worked for me for over 40 years.  I don't recall where I learned that trick.  Since it air cures, the caulk needs to be applied in thin (3-5mm thick layers) and left to cure overnight.  Since a squeeze tube is less then $ 7.00 cost isn't s problem for most of us.  When you finish with the mold, you can earn points with the local Goddess by re-caulking the seams in her kitchen back-splashes with the leftovers.
Logged
SandiaPaul
Sr. Member
****
Offline Offline

Posts: 319


« Reply #5 on: June 27, 2018, 04:06:15 AM »

When I did this professionally I used these folks:
https://bjbenterprises.com/index.php/

They sell quart kits of silicones. They were always very helpful too and I see their site now has loads of good how to info and videos.

Paul
Logged

Paul
Pages: [1]
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.13 | SMF © 2006-2011, Simple Machines LLC Valid XHTML 1.0! Valid CSS!